Top Bend LED Neon Flex

24 V DC · SILICONE NEON FLEX SUPPLIER

Specify the right profile for your project

Specify a top bend LED neon flex profile for your architectural light line. Compare 17 catalog configurations, from compact white-light profiles to 20 m runs, three-side emission and all-black options.

For contractors, distributors and OEM buyers. Match the size, bending route, light output and connection detail before requesting samples or pricing.

24 V DC input · IP67 catalog rating · Fixed white · CCT and selected SPI-RGB configurations

Top bend LED neon flex raw roll silicone neon light for custom lighting projects
1616 top bend neon flex · 20 m catalog configuration
YEARS EXPERIENCE
0 +
GLOBAL CLIENTS
400 +
HOUR LIFESPAN
0 K
COUNTRIES SERVED
40 +

PROFILE SELECTION

Compare sizes and configurations

Select both the profile and its variant. The same outer size can have a different LED density, cut interval, light output or control requirement.

01

/STANDARD WHITE

Compact to wide white-light profiles

Six profiles for different recess widths and visible light-line sizes. Start with the outer dimensions, then check the mounting fit and the approved bending geometry.

Top Bend LED Neon Flex warm white vertical bend silicone neon flex, dot-free uniform linear lighting for architectural outline
0606 · compact white-light profile
Profile Outer size
W × H (mm)
Light / control LEDs/m Cut
(mm)
Power
(W/m)
Output
(lm/m)
Nominal
length (m)
0606
6 × 6
White
240
25
8
400–440
5
0610
10 × 6.5
White
280
50
9.6
365–430
5
1313
13 × 13
White
120
50
9.6
380–580
5
3020
30 × 20
White
240
50
18
720–1010
5
4025
40 × 25
White
276
50
18
740–1050
5
5025
50 × 25
White
276
50
18
740–1050
5

24 V DC · IP67 catalog rating. White configurations: 3000 K ±150 K, 4000 K ±200 K or 6500 K ±300 K; CRI Ra ≥90.

02

/ 20 M CONFIGURATIONS

Four profiles for longer runs

These four catalog configurations use a constant-current strip design with copper strips and are listed for single-end supply over a 20 m length. They still use a 24 V DC input; confirm the driver, cable size and installed run before ordering.

Warm CCT Top Bend LED Neon Flex coiled sample, vertical bend silicone neon flex, decorative linear LED lighting
1212 · 20 m configuration
Profile Outer size
W × H (mm)
Light / control LEDs/m Cut
(mm)
Power
(W/m)
Output
(lm/m)
Nominal
length (m)
1010
10 × 10
White
120
50
8
340–420
20
1212
12 × 12
White
120
50
8
340–430
20
1616
16 × 16
White
120
50
8
330–430
20
2020
20 × 20
White
120
50
8
330–430
20

24 V DC · IP67 catalog rating. White configurations: 3000 K ±150 K, 4000 K ±200 K or 6500 K ±300 K; CRI Ra ≥90.

03

/ THREE-SIDE EMISSION

White light visible from three sides

Choose these profiles when the luminous surface needs to remain visible from more than one viewing angle. Three-side emission describes the diffuser, not three-dimensional bending.

1. `Coiled Top Bend LED Neon Flex, waterproof silicone vertical bend neon flex for facade and ceiling cove lighting`
1616 · three-side emitting profile
Profile Outer size
W × H (mm)
Light / control LEDs/m Cut
(mm)
Power
(W/m)
Output
(lm/m)
Nominal
length (m)
1010
10 × 10
White
120
50
11
490–600
5
1212
12 × 12
White
120
50
9.6
560–680
5
1616
16 × 16
White
120
50
9.6
525–670
5
2020
20 × 20
White
120
50
9.6
515–670
5

24 V DC · IP67 catalog rating. White configurations: 3000 K ±150 K, 4000 K ±200 K or 6500 K ±300 K; CRI Ra ≥90.

04

/ ALL-BLACK

Black appearance, distinct light configurations

The 1010 is a fixed-white configuration. The 1616 and 2020 are SPI-RGB configurations requiring matched control equipment. Their catalog light-output ranges differ substantially from the white-body profiles; approve the lit and unlit sample appearance.

White Top Bend LED Neon Flex sample, vertical bend silicone neon flex, dot-free uniform lighting for architectural facade lighting
1010 · all-black fixed-white profile
Profile Outer size
W × H (mm)
Light / control LEDs/m Cut
(mm)
Power
(W/m)
Output
(lm/m)
Nominal
length (m)
1010
10 × 10
White
144
41.66
11
10–80
5
1616
16 × 16
SPI-RGB
84
71.43
14
11–130
5
2020
20 × 20
SPI-RGB
84
71.43
14
10–120
5

24 V DC · IP67 catalog rating. White configurations: 3000 K ±150 K, 4000 K ±200 K or 6500 K ±300 K; CRI Ra ≥90. CCT and CRI apply to the 1010 white version only; they do not describe the 1616/2020 SPI-RGB versions.

Length and light output: nominal length is the catalog supply length, not a universal maximum feed distance. End caps and cable exits affect finished assembly dimensions. Lumen ranges are catalog values, not a guaranteed result for every color or operating condition; confirm the selected configuration.

MATCH THE LIGHT LINE

Choose the bend plane before the profile size

Top bend describes a permitted bending plane. Mark the emitting face on your layout and check every curve against the selected model’s drawing. Avoid twisting, sharp folds or forcing the profile sideways.

Curved architectural details

Use a top bend profile when the planned arc follows its allowed bending plane. Send the smallest curve and the mounting orientation for confirmation.

Long contour lighting

Compare the four 20 m catalog configurations when feed-point access matters. Confirm the driver and cable route as part of the lighting layout.

Visible decorative lines

Compare white-body, three-side and black profiles by their actual sample appearance, both lit and unlit. Three-side emission does not make a profile bend in three dimensions.

Top Bend LED Neon Flex 16*16 mm dimension drawing, 50 mm cutting distance, 20 m roll length, silicone vertical bend neon flex
1616 long-run profile dimensions and 50 mm cut interval · catalog page 6

Approve the geometry

The catalog provides profile and accessory drawings, but it does not establish one lamp-body bend radius for this full range. Ask for the exact model’s bending plane and minimum radius or diameter.

BUILD THE COMPLETE ASSEMBLY

Specify end caps, cable exits and mounting together

Top Bend LED Neon Flex end cap and cable options, wrapped end caps & uniform-width end caps, side/straight/bottom cable outlet
1616 example: wrapped and uniform-width end caps and cable-exit options · catalog page 6

End caps and lead positions

State straight, side or bottom cable exit where the selected model supports it. Wrapped and uniform-width end caps have different assembly envelopes. Some catalog options require customization; approve the end-cap drawing and finished length in the quotation.

Top Bend LED Neon Flex mounting accessories, 19*18mm aluminum profile, 17.5*18mm 3D flexible profile, minimum bend diameter ≥120mm
1616 example: mounting clip, straight channel and flexible aluminum channel · catalog page 6

Clips and channels

Select hardware for the actual outer dimensions and installation route. The illustrated flexible-channel diameter belongs to that accessory drawing; it is not a general lamp-body bend-radius specification. Check channel fit on a sample.

Coordinate cutting and sealing before the order. Use installation guidance for clips and channels and review dimensional tolerances and mounting fit alongside the model-specific drawing.

For other non-standard customizations, please provide detailed specifications—such as specific color temperature (CCT), RGBW, DMX512, 98CRI, 48V voltage, IP68, SDCM <3, or specific dimensions/molding requirements.

POWER & CONTROL

Match the 24 V supply to the exact configuration

Fixed-white configurations

Select the required CCT and power per meter. State any dimming requirement so the driver/controller combination can be checked. A list of CCT options does not mean the product is tunable white.

20 m catalog variants

The 1010, 1212, 1616 and 2020 long-run variants use the specified strip design for single-end supply. An internal constant-current circuit does not mean that an arbitrary external constant-current driver is suitable.

All-black SPI-RGB

For 1616 and 2020 SPI-RGB, confirm the IC, compatible controller, addressable sections and wiring. Do not infer pixel count from LEDs/m or assume direct DMX support.

Size the system from the load: selected W/m × connected meters gives the nominal LED load. Then check the driver’s rating and derating conditions, cable voltage drop, controller capacity and feed arrangement. These products require the specified low-voltage DC supply; do not connect them directly to AC mains.

Explore Mean Well LED power supplies and request a matched power-and-control configuration for the route and installation environment.

SAMPLE TO PRODUCTION

Approve a sample that represents the order

01 / Fit and geometry

Check external dimensions, the selected clip or channel, emitting-face orientation, cable exits and the smallest approved curve.

02 / Light and operation

Check the selected white tone or SPI effect, measured power and brightness along the intended run with the proposed supply and control equipment.

03 / Assembly and records

Record end caps, sealing, finished lengths and the approved drawing. Agree acceptance limits and identification requirements for repeat orders.

For project submittals, request certificates or test reports covering the exact configuration and destination market. Match the document’s model list and test conditions to the proposed order. Use the document request route and learn more about NPHIS.

Order and production

Standard MOQ: USD 1,000 order value. Production with available materials is typically about 5–7 days; fully customized orders are typically about 15–30 days, depending on quantity and complexity. The quotation confirms sample costs, production timing and shipping scope.

Commercial warranty

Standard warranty: 3 years. Eligible special or custom configurations may receive up to 5 years under agreed quotation terms. This is not automatic coverage for every custom order and is not an operating-lifetime claim.

PRODUCT DOCUMENTS

Keep the catalog and order drawing together

Our LED Neon Flex Catalog covers this Top Bend range on printed pages 1–17 (PDF pages 4–20). Use it to shortlist a profile, then request the current drawing and configuration details for the order.

For a model-specific drawing, test document or installation detail, send a document request with the profile and destination market.

PRODUCTION & DOCUMENTATION

Equipment and compliance documents

An integrating sphere measures light output and color. The SMT line places LEDs on the circuit board, and the temperature and humidity chamber supports environmental testing. When requesting test data, specify the profile, CCT and operating conditions you want evaluated.

EMC and RoHS documents for NPHIS LED Neon Strip

This document lists Shanghai Leimei Optoelectronics Technology Co., Ltd. as the applicant and manufacturer, and NPHIS as the trademark. The list of model numbers covers all the top bend neon flex strip dimensions shown in the table above. Please provide the ordered configuration and the target market so that we can match the documentation to your purchase.

Certificate of Conformity document from HTT Technology showing certificate number, applicant and manufacturer details, product (LED Neon Strip) and signature area.
EMC · HTT202606891E
HT Technology Certificate of Conformity page showing product: LED Neon Strip with RoHS compliance and certificate details.
RoHS · HTT202606891R

BUYER QUESTIONS

Top Bend LED Neon Flex FAQs

Answers for profile selection, installation planning and wholesale purchasing. Match the answer to the specific catalog variant and the agreed order configuration.

Selection and bending

Top bend LED neon flex is an LED strip inside a flexible silicone diffuser, designed to bend in one specified plane. It creates a continuous-looking light line for architectural accents and outlines. In this NPHIS series, the catalog input is 24 V DC. Select the profile by its light-emitting face, cross-section and permitted bend direction.

Choose the outer width and height that fit the recess and the intended visible light line. This range spans 6 × 6 mm to 50 × 25 mm, with separate long-run, three-side and black variants. The 0610 drawing shows 10 × 6.5 mm, so its name is not a dimension substitute. Check the profile and channel fit on a sample.

The difference is the permitted bending plane relative to the emitting face. Top bend and side bend profiles are not interchangeable at every turn. Mark the emitting face and the route on your drawing, then match the profile to it. A straight line alone does not prove that only top bend will work. See the Top Bend selection guide for further discussion.

There is no single confirmed lamp-body bend radius for all 17 configurations on this page. Request the model-specific drawing with the bending plane and minimum radius or diameter clearly marked. The diameter values shown beside flexible aluminum channels in the catalog describe those illustrated accessories and must not be reused as a universal neon-strip bend radius.

A 90-degree change in direction needs an approved curved route or a suitable connection detail; do not make a sharp fold in the silicone body. The route must stay in the permitted bending plane and respect the selected model’s minimum bend dimension. Send the corner drawing, emitting-face orientation and available space so the assembly can be checked before manufacture.

The choice depends on the required appearance and installation. This silicone LED neon flex offers a flexible diffuser and a 24 V DC input for modular architectural lighting. Glass neon uses formed glass tubing and a different electrical system. Compare the actual visual result, support, connections and service access; do not assume a universal energy-saving percentage or service life for either option.

Installation, power and control

Yes, at the marked cutting points for the selected configuration. The catalog lists 25 mm for 0606, 41.66 mm for 1010 all-black, 71.43 mm for 1616/2020 all-black and 50 mm for the other listed variants. Switch off power before cutting. The finished length also needs room for end caps and cable exits; outdoor cuts require the approved sealing method.

The catalog lists IP67 for these profiles, but an outdoor order must specify the complete assembly, including end caps, cable entry, joints and any field cuts. IP67 is not a promise of permanent underwater service. Send the exposure conditions and destination requirements, and request the applicable assembled-product documentation before approving the configuration.

The catalog identifies 1010, 1212, 1616 and 2020 long-run variants for 20 m single-end supply with their specified strip design. That capability does not apply automatically to the 5 m white, three-side or black variants. Confirm the actual load, cable route, supply voltage and installed brightness with the selected configuration before approving the project.

The catalog’s 1010 all-black profile is fixed white. The 1616 and 2020 all-black profiles are SPI-RGB, not direct-DMX products by default. Their IC type, addressable section size and controller compatibility must be confirmed for the order. LED count is not the same as pixel count. If your project uses DMX, request a matched interface and control proposal.

Dimming must be specified for the complete system. Tell NPHIS whether the project requires PWM, DALI, 0–10V or another method so a compatible driver or controller can be proposed and sample-tested. This catalog does not establish universal compatibility or built-in DALI/0–10V support for every profile. Start with matched LED power supplies and confirm the exact control configuration.

Use mounting hardware matched to the profile and the route. The catalog shows model-specific clips and, for many sizes, straight and flexible aluminum channels. Compare support, straightness, recess depth and service access; do not force an oversized body into a narrow channel. Review the neon flex mounting guide and approve the actual profile-and-channel fit on a sample.

Samples, documentation and ordering

Request a sample configuration before approving a bulk order. NPHIS’s standard minimum order value is USD 1,000; this is an order-value threshold, not a 1,000 m requirement. Sample availability, sample charges and shipping are confirmed in the quotation. Include the profile, variant, color, lengths and intended mounting hardware so the sample represents the proposed order.

Production using available materials is typically about 5–7 days. Fully customized orders are typically about 15–30 days, depending on quantity and process complexity. The quotation confirms the applicable schedule. These are production estimates, not guaranteed delivery dates; sample approval, special components, document requirements, shipping and customs can affect the overall project schedule.

Approve a representative sample and its written configuration: external dimensions, mounting fit, emitting face, color, measured power, run length, end caps, cable exits and control behavior. Record the acceptance method and agreed limits on the drawing or order. Keep that approved reference for repeat orders, including any agreed color-matching and batch-identification requirements.

Request the documents required for your exact model, configuration and destination market. Check the certificate or report holder, model coverage and relevant test conditions. Catalog logos do not prove that every variant has every approval. Start with the compliance document request route and list any required CE/RoHS, market-specific approval or ingress-protection evidence in your RFQ.

NPHIS’s standard commercial warranty is 3 years. Eligible special or custom configurations may receive up to 5 years under the agreed quotation terms; this is not automatic for every custom order. Warranty coverage and operating lifetime are different. This catalog does not establish a universal rated lifetime for all listed variants, so request the applicable warranty terms and any required lifetime evidence separately.

Send the profile and variant, color or CCT, total quantity, individual finished lengths, bending layout, mounting method, cable exits, environment, control system and destination. State whether the quote should include end caps, connectors, channels, drivers, controllers, packaging and shipping. This makes the supply scope comparable. Request a Top Bend project quotation with your drawing or bill of materials.

REQUEST A PROJECT QUOTE

Send your Top Bend neon flex requirements

Tell us what the light line needs to do and which catalog profiles you are considering. Include the details below in your message so the quotation can identify the product and complete supply scope.

  • Profile, variant, quantity and individual finished lengths
  • White CCT or SPI-RGB effect and control requirements
  • Bending layout, emitting-face orientation and mounting method
  • Indoor/outdoor conditions, cable exits and feed locations
  • Destination, required documents and project timing

Prefer a separate enquiry? Open the project quotation page. For contact details, visit Contact NPHIS.

主页联系表单
Scroll to Top